Wakol D3125 Dispersion glue for PVC (content 10kg)
- Buy 3 for €148,45 each and save 1%
- Buy 10 for €146,95 each and save 2%
- Buy 25 for €142,45 each and save 5%
| Article number: | 14660 |
- Mo/Fr ordered before 18.00 is shipped directly
- Laagste prijs tot wel 75% korting !
- Houtafwerkingsspecialisten sinds 1976
- Grootste voorraad van de Benelux (+1000m2)
- Reeds 200.000+ tevreden klanten
- Customer service from 10:00 to 18:00
Wakol D3125 Dispersion glue for PVC (content 10kg),
Dispersion adhesive according to DIN EN 14259 for installation in the adhesive bed system of
• PVC design floor covering
• Homogeneous and heterogeneous PVC floor coverings in rolls and tiles
• Cushion-Vinyl floor coverings on properly prepared absorbent and non-absorbent indoor surfaces.
• Free of solvents according to the definition of the TRGS 610
• very long waiting time
The substrate as well as the climatic conditions must meet the requirements of the valid standards and data sheets. Subfloors must be permanently dry, dimensionally stable, flat, free of cracks, contaminants and substances that could impair the adhesion.
Level very uneven surfaces with a Wakol leveling compound. The technical information of the primers and the leveling compounds must be adhered to.
Instructions
Stir the glue well before use. Apply evenly to the substrate with the notched trowel, avoiding adhesive build-up. After the specified waiting time, fit the floor covering into the adhesive bed and press on well. Rub after a short time; Roll again approximately 1 hour after laying.
Easy, fast and healthy bonding of large areas of PVC floor.
WAKOL's flagship product is the WAKOL D 3125 PVC-Design floor covering adhesive. WAKOL D 3125 is qualitatively the best choice for gluing your PVC floor! Why? Well, here's why:
- Can be used quickly and for a very long time (up to 180 minutes!)
- Is ideal for installing PVC design floor coverings, homogeneous and heterogeneous PVC floor coverings in rolls and tiles
- Suitable for both absorbent and non-absorbent indoor subfloors
- Has a lower consumption! This glue is applied directly with the TKB A1 trowel. The consumption is only 190 to 220 g/m², which is considerably less than with conventional wet-bed adhesives. At the same time, this also means that less material needs to be taken to the construction site.
- Is very low-emission, so also a healthy choice.
Glue of the new generation – advantages of all systems in one
Laying PVC design floor coverings and PVC and CV floor coverings in strips and tiles
WAKOL D 3125 PVC-Design floor covering adhesive combines the advantages of the existing systems:
- Glue security and firmness with wet bed
- Long exposure time of a contact adhesive
- Low consumption of a roller adhesive
Glue security and firmness with wet bed
Even three hours after application, WAKOL D 3125 PVC-Design floor covering adhesive still meets the requirements of DIN standard 14259. The adhesive significantly outperforms the required peel and shear strengths. Like a wet bed adhesive, WAKOL D 3125 PVC-Design Floor Covering glues the floor coverings firmly to the substrate. The extremely low-emission WAKOL D 3125 PVC-Design floor covering adhesive is classified in EMICODE class EC1 PLUS.
Sustainable thanks to low consumption and high efficiency
Unlike roller adhesives, the leveling compound does not need to be primed. WAKOL D 3125 PVC-Design floor covering adhesive is applied directly with the TKB A1 trowel. The consumption is only 190 to 220 g/m², which is considerably less than with conventional wet-bed adhesives. At the same time, this means that less material needs to be taken to the construction site. As a standard-compliant and construction-approved adhesive, it is suitable for tenders and public spaces.
Long waiting time
After the drying time, there is up to three hours to install the floor coverings in the adhesive bed. This makes it possible to glue large surfaces with WAKOL D 3125 PVC-Design floor covering adhesive. Even floor coverings in complex patterns or intricate spaces can now be installed without any problems and without time pressure.
Fast and easy processing
WAKOL D 3125 PVC-Design floor covering adhesive is suitable for absorbent and non-absorbent substrates. The adhesive can be applied very smoothly with the TKB A1 trowel and is therefore easy to apply. Because of these properties, WAKOL D 3125 PVC-Design floor covering adhesive can also be easily applied standing up with the appropriate tools. Proven installation techniques in a new form: with WAKOL D 3125 PVC-Design floor covering adhesive, glue can be applied again while leaning on the newly installed PVC floor without glue coming out of the joints. The surface can be walked on immediately after laying the floor covering.
Please note glue and related products have different return conditions.
