Wakol MS550 Polymer PVC and Rubber Glue content 7.5 kg
| Article number: | 13428 |
- Mo/Fr ordered before 18.00 is shipped directly
- Laagste prijs tot wel 75% korting !
- Houtafwerkingsspecialisten sinds 1976
- Grootste voorraad van de Benelux (+1000m2)
- Reeds 200.000+ tevreden klanten
- Customer service from 10:00 to 18:00
Wakol MS 550 Polymer PVC and Rubber Glue (contents 7.5 kg),
For the installation of homogeneous and heterogeneous PVC floor coverings on rolls and tiles, PVC design floor coverings, CV floor coverings as well as rubber floor coverings on rolls and tiles, needle felt floor coverings, linoleum, PVC cork floor coverings, artificial grass and walk-in mats on absorbent and non-absorbent subfloors indoors and outhouse. Waterproof. WAKOL MS 550 complies with DIN EN 14259.
WAKOL MS 550 PVC and rubber adhesive - first MS adhesive for PVC floor coverings
Modern reaction adhesive for elastic floor coverings
With WAKOL MS 550 PVC and rubber adhesive, it is now possible for the first time to safely carry out demanding installations that previously had to be carried out with 2-component PU adhesive, using a modern one-component MS adhesive.
Very wide application spectrum
WAKOL MS 550 PVC and rubber adhesive is suitable for bonding all PVC floor coverings as well as PVC design floor coverings in rubber floor coverings. It does not matter whether you want to place on absorbent or non-absorbent surfaces, inside or outside the floor covering.
For the highest demands on the installed surface
Zones with high moisture values, such as access zones or zones with increased heat load from sunlight, such as conservatories, can be installed reliably with WAKOL MS 550 PVC and rubber adhesive. Challenges such as surfaces with forklift traffic and heavy loads are met by the safe and firm bonding.
Start immediately and use surface quickly
Without laborious mixing, WAKOL MS 550 PVC and rubber adhesive is applied directly from the bucket to the prepared substrate. Due to the possibility to also use the adhesive on non-absorbent substrates, primed or closed substrates can also be treated directly with, for example, WAKOL PU 280 Polyurethane Primer or WAKOL MS 325 Silane Primer.
Processing comfort and safe application
WAKOL MS 550 PVC and rubber adhesive is characterized by a very low compression tendency. When working unavoidably on the floor covering, such as when installing floor covering on a roll, knee marks in the surface are minimized. Due to the high initial adhesion and the fast drying, PVCdesign floorcoverings lie firmly in place right from the start. Adhesive that gets on the floor covering surface can get in
fresh and cured condition can be removed without leaving any residue. Due to the hard adhesive beads of WAKOL MS 550 PVC and rubber adhesive, residual impressions are minimized as well as with a fibrous dispersion adhesive.
Long shelf life due to sealed bucket
WAKOL MS 550 PVC and rubber adhesive is supplied in a practical plastic bucket. An aluminum compound foil, which is welded to the edge of the bucket, provides the best possible protection against moisture and guarantees a storage stability of at least 12 months. Curing in the unopened original bucket and the associated loss of material and additional costs are thus excluded.
Economic
As a 1-component product, the use of WAKOL MS 550 PVC and rubber adhesive eliminates the troublesome and laborious mixing. This means that, unlike in the past for 2-component PU glue, you do not need a mixer power on the construction site. You will not be annoyed by dirty stirring tools or loss of time due to mixing. Mixing errors are also a thing of the past. Waiting times are no longer necessary for this modern product. You do not lose money due to cured residues, which are unavoidable with 2-component products. After covering the residual amount and closing the bucket, the adhesive can be used for subsequent work. There is therefore hardly any residual waste.
Please always observe the technical information before processing
--TECHNICAL INFORMATION--
